Bedienungsanleitung Lindy 43108
Sprache(n):
Englisch
Dateigröße:
131,04KB
Downloadzeit:
DSL 16k: 1s
Downloads bisher: 30
Hersteller:
Lindy
Speichergehaeuse Lindy 43108
Vorschau Lindy 43108 Handbuch:
English Manual English 2 Device Overview Hardware Installation 1. Unlock upper and lower covers, then open the door. HDD ACTIVE LED POWER LED LOCK HOLE HDD GATE HDD ACTIVE LED Mode Select USB 3.0 Power Switch DC Jack English Manual English 3 2. Place one or two hard drive(s) in the slot. Make sure the SATA connector is lined up with the connector inside the Mobile Rack. 3. Carefully push the hard drive into the Mobile Rack, so that the drive’s SATA connector is seated securely, then close the door and lock it. It must be in the lock position when in use. This prevents unexpected removal while working. 4. Adjust the DIP switch to set the storage policy: 5. Plug the included switching power adapter into the enclosure´s power adapter jack, then plug the switching power adapter into a reliable power source. 6. Use the included USB 3.0 cable to plug the USB 3.0 Dual 2,5“ SATA Mobile RAID into a USB 3.0 port of your computer and switch it on. Make sure the Power LED is lit. Caution: Changing the RAID mode destroys data stored on the Mobile Rack, If you have saved data on the drives, back up data before following these steps. Note: 1. Users are advised to disable the device from the computer before unplugging the cable or turning off the device. 2. If the hard drive does not support ACCESS signal, then the HDD ACTIVE LED will not flash when the hard drive is in use. 3. If the system cannot detect the device, please go to device management and enable it. 4. Do not open the door or turn off the power of the Mobile Rack while the hard drive is busy, this may cause damage to you hard drive. 5. It must be in the lock position when in use. This prevents unexpected removal while working. 6. Do not force the door to open while it is locked, otherwise, you will damage the lock. Driver Installation Windows will automatically detect and install the drivers. An additional drive icon will appear in MY COMPUTER when the USB 3.0 Dual 2,5“ SATA Mobile RAID is connected. 1: ON 2: ON 1: ON 2: OFF 1: OFF 2: ON 1: OFF 2: OFF English Manual English 4 Disconnecting from the Computer Use Windows’ Safely Remove Hardware utility to turn off or disconnect the USB 3.0 Dual 2,5“ SATA Mobile RAID. Windows 7 1. Verify that the HDD access LED is OFF before proceeding 2. Click the Safely Remove Hardware and Eject Media icon located in the taskbar 3. Click the „USB Mass Storage Device“ 4. When the message Safe to Remove Hardware pops up, you can safely turn off or unplug the enclosure Windows Vista 1. Verify that the HDD access LED is OFF before proceeding 2. Double click the Unplug or Eject Hardware icon located in the syste .....
English Manual English 2 Device Overview Hardware Installation 1. Unlock upper and lower covers, then open the door. HDD ACTIVE LED POWER LED LOCK HOLE HDD GATE HDD ACTIVE LED Mode Select USB 3.0 Power Switch DC Jack English Manual English 3 2. Place one or two hard drive(s) in the slot. Make sure the SATA connector is lined up with the connector inside the Mobile Rack. 3. Carefully push the hard drive into the Mobile Rack, so that the drive’s SATA connector is seated securely, then close the door and lock it. It must be in the lock position when in use. This prevents unexpected removal while working. 4. Adjust the DIP switch to set the storage policy: 5. Plug the included switching power adapter into the enclosure´s power adapter jack, then plug the switching power adapter into a reliable power source. 6. Use the included USB 3.0 cable to plug the USB 3.0 Dual 2,5“ SATA Mobile RAID into a USB 3.0 port of your computer and switch it on. Make sure the Power LED is lit. Caution: Changing the RAID mode destroys data stored on the Mobile Rack, If you have saved data on the drives, back up data before following these steps. Note: 1. Users are advised to disable the device from the computer before unplugging the cable or turning off the device. 2. If the hard drive does not support ACCESS signal, then the HDD ACTIVE LED will not flash when the hard drive is in use. 3. If the system cannot detect the device, please go to device management and enable it. 4. Do not open the door or turn off the power of the Mobile Rack while the hard drive is busy, this may cause damage to you hard drive. 5. It must be in the lock position when in use. This prevents unexpected removal while working. 6. Do not force the door to open while it is locked, otherwise, you will damage the lock. Driver Installation Windows will automatically detect and install the drivers. An additional drive icon will appear in MY COMPUTER when the USB 3.0 Dual 2,5“ SATA Mobile RAID is connected. 1: ON 2: ON 1: ON 2: OFF 1: OFF 2: ON 1: OFF 2: OFF English Manual English 4 Disconnecting from the Computer Use Windows’ Safely Remove Hardware utility to turn off or disconnect the USB 3.0 Dual 2,5“ SATA Mobile RAID. Windows 7 1. Verify that the HDD access LED is OFF before proceeding 2. Click the Safely Remove Hardware and Eject Media icon located in the taskbar 3. Click the „USB Mass Storage Device“ 4. When the message Safe to Remove Hardware pops up, you can safely turn off or unplug the enclosure Windows Vista 1. Verify that the HDD access LED is OFF before proceeding 2. Double click the Unplug or Eject Hardware icon located in the syste .....
